.::Rezerwa 126p::. Strona Główna .::Rezerwa 126p::.
BEZ KOMUNISTYCZNEJ ADMINISTRACJI

FAQFAQ  SzukajSzukaj  UżytkownicyUżytkownicy  GrupyGrupy  StatystykiStatystyki
RejestracjaRejestracja  ZalogujZaloguj  AlbumStrona główna

Poprzedni temat «» Następny temat
Oil leak from carburettor/Oil in airfilter tube
Autor Wiadomość
don.giannis 

Dołączył: 08 Mar 2024
Posty: 6
Skąd: Slovenia
Wysłany: 2024-08-21, 18:56   Oil leak from carburettor/Oil in airfilter tube

My carburettor is leaking oil from the gasket and the oil also appears in the airfilter tube.
What is causing this and how should I fix it? Engine works fine, without power loss and the level of oil is correct.

Thank you for your responses.
  
 
     
michals 

Wiek: 46
Dołączył: 17 Lut 2015
Posty: 657
Skąd: Limanowa
Wysłany: 2024-08-21, 19:15   

It probably comes from oil pneumothorax. For the test try to put one end of pipe to the bottle and check how much oil appears.
 
     
romek 


Dołączył: 30 Mar 2016
Posty: 684
Skąd: Ostróda
Wysłany: 2024-09-06, 17:25   

Fiat 126 has a tendency to throw oil out of the pneumothorax because the two pistons run together and the pressure in the engine block is high. If there is a lot of oil and it is leaking outside, check whether there is a wire strainer inside pipe in the valve cover. If there is a strainer in the cover, you need to check the piston rings by sampling the oil. I think you will find how to do it on the Internet. The correct compression pressure is at least 8 Bar, after pouring oil into the cylinder it cannot increase more than 0.5 Bar.
_________________
Były:

'86 Polski Fiat 126p ZFA Bleu Lord (2003-2010)
'99 Fiat 126 ELX Maluch Town SX 90's Style (2016-2019)

Jest:
'93 Polski Fiat 126p FL-2 454 Szmaragd (2023- )
 
     
don.giannis 

Dołączył: 08 Mar 2024
Posty: 6
Skąd: Slovenia
Wysłany: 2024-09-07, 11:21   

I installed oil catch can and It's getting oil inside.
That means the piston rings are bad? Engine works fine, without any problems.
I'll get some tools needed for the pressure test and try it.
And I think there's no wire strainer. How does it look?

Thanks!
 
     
romek 


Dołączył: 30 Mar 2016
Posty: 684
Skąd: Ostróda
Wysłany: 2024-09-07, 19:54   

https://archiwum.allegro.pl/oferta/tlumik-wygaszacz-plomieni-fiat-126p-polonez-i7215839374.html

You have photo in the link. It is to be mounted in the valve cover, in the pneumothorax connector. If this is not there, this may be the cause of your problem.
_________________
Były:

'86 Polski Fiat 126p ZFA Bleu Lord (2003-2010)
'99 Fiat 126 ELX Maluch Town SX 90's Style (2016-2019)

Jest:
'93 Polski Fiat 126p FL-2 454 Szmaragd (2023- )
 
     
don.giannis 

Dołączył: 08 Mar 2024
Posty: 6
Skąd: Slovenia
Wysłany: 2024-09-17, 16:44   

I installed wire strainer inside breather pipe and oil filler vapour filter.
I drove 35km and there's quite much oil in catch can.
I also did compression test. I have 7.5 bar on cylinder 1 and 7 bar on cylinder 2.
With oil cylinder 1 is 7.5 bar and cylinder 2 is 8 bar.
What is the best way to change piston rings and how to install/rotate them correctly?
Or is the best way to change cylinders and pistons? Engine has 90.000 km.
And which is the best engine oil?
  
 
     
romek 


Dołączył: 30 Mar 2016
Posty: 684
Skąd: Ostróda
Wysłany: 2024-09-28, 20:35   

Sorry for the late reply. In fact, the engine qualifies for renovation. If poor quality oil was used, it is possible at this mileage. To know whether only the piston rings can be replaced, you need to measure the cylinder wear using a specialized device (diameter gauge). If the cylinder wear is high, the cylinder should be ground and larger pistons should be purchased, or buy new repair kit: cylinders, pistons and ringa . If you want to do it yourself, it's best to find a tourtrial on YouTube because it's a lot of writing. You need to remove the sheet metal casing, head, exhaust, oil pan, unscrew the connecting rods and take out the pistons with the cylinder up. Ring locks every 120 degrees, it matters which side the piston is mounted on (the connecting rods have numbers 1 and 2, these numbers are probably for the camshaft). read the topic: http://forum.rezerwa126p....032c15b5#522957

When it comes to oil, it is a sensitive topic on the 126p forum. The manual recommends 10w-30 to 20w-50, and each user has a different opinion. Probably the most popular choice is mineral 15w-40, if the engine used for sports is 10w60. Choose a good brand, for example ELF.
_________________
Były:

'86 Polski Fiat 126p ZFA Bleu Lord (2003-2010)
'99 Fiat 126 ELX Maluch Town SX 90's Style (2016-2019)

Jest:
'93 Polski Fiat 126p FL-2 454 Szmaragd (2023- )
  
 
     
michals 

Wiek: 46
Dołączył: 17 Lut 2015
Posty: 657
Skąd: Limanowa
Wysłany: 2024-09-29, 10:39   

Before engine re-asembly you can try to flush engine: https://allegro.pl/listing?string=p%C5%82ukanka%20do%20silnika

If the rings are weak nothing change, but usually hepls.
 
     
Wyświetl posty z ostatnich:   
Odpowiedz do tematu
Nie możesz pisać nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz głosować w ankietach
Dodaj temat do Ulubionych
Wersja do druku

Skocz do:  

Powered by phpBB modified by Przemo © 2003 phpBB Group
Rusztowania Szalunki
Strona wygenerowana w 0,03 sekundy. Zapytań do SQL: 16